FREE shipping on orders over $50

Shopping cart

Your cart is currently empty

Product image slideshow Items

  • Inertia Inertia V2 Tungsten Alloy CSK Screws - 10pcs
  • Inertia Inertia V2 Tungsten Alloy CSK Screws - 10pcs
  • Inertia Inertia V2 Tungsten Alloy CSK Screws - 10pcs
  • Inertia Inertia V2 Tungsten Alloy CSK Screws - 10pcs

Inertia V2 Tungsten Alloy CSK Screws - 10pcs

Excl. tax

The rating of this product is 0 out of 5

On backorder

Inertia V2 Tungsten Alloy CSK Screws - 10pcs 


Introducing an industry first – Tungsten weighted screws

  • Inertia's Tungsten alloy is 225% heavier than steel, 200% heavier than brass, and 150% heavier than lead.
  • Inertia’s Proprietary Tungsten Alloy screws weigh in at an impressive 4.3 grams per 5x - 6mm screws vs 1.8 grams for standard steel screws.
  • Yield's a 3.5 gram net gain per 5x screws used - at the lowest place in the car. Yield can be even greater when you use 8mm in place of 6mm screws where possible.
  • Frees up valuable space on top of the chassis.
  • Gives greater ability to place electronics and weight exactly where you want them.
  • Can also be useful to tune the vehicle - with weight bias. This is easily done by isolating the Inertia Tungsten Screws to one area of the car.

There are a select few ways to increase corner speed; one of which is to lower the Center of Gravity in your car - or simply placing weight as low as you can. Inertia Tungsten screws put the most weight at the lowest possible point; the bottom of the chassis.

"Simply switching a car over to Tungsten screws allows for more corner speed, and faster laps."

Lastly, our Tungsten Screws have been tested against several brands of steel screws. The team have found that they've outlasted steel screws (head deformation) and did not deform like some steel screws can over time. This is due to Inertia's proprietary Tungsten Alloy formula.

These v2 tungsten screws have an even heavier and more durable formula, than our first batch. Most importantly they now have a true 2mm hex, with the same amazing specifications as our other Inertia screws!

  • Sold in 2 quantities - 3 and 10 pieces.
  • Available in M3 sizes.
  • 10% quantity discount if 10+ individual screws ( 1x 10pc set ! ) are purchased.

Why are Tungsten Screws so expensive ?

Tungsten is very difficult to work with and the process to do so is very costly. Fortunately, we've done all the work necessary to ensure a quality product that you should be able to use over a long period of time - This assumes that they're used in a manner consistent with what they were developed for of course.

Are they worth the money ?

This is strictly an individual choice. For the racer that's looking for that extra little bit, that special elusive edge over their competition - this is almost a must-have, especially in higher grip situations. For the hobbyist and the like, these are probably not for you .. there are definitely other more important things to spend on.

How much can I tighten them?

We recommend the Three Finger Method - basically you hold your driver with your thumb, index, and middle fingers only and only tighten until the driver begins to slip in your fingers and no more. Tungsten screws are tough but they can and will break if over tightened. Using this method will ensure that the screw is tight enough without risking breakage. (instructional video coming soon)

Can I use Loctite or thread lock ?

Absolutely NO !!

When following the three finger method, a screw shouldn't come loose when being regularly maintained. In the very unlikely event of a breakage, you will quite literally never be able to remove it from whatever it's screwed in to. Tungsten is one the hardest materials around and cutting or drilling it out is extremely unlikely. Proceed at your own risk.

0 stars based on 0 reviews
Add your review